Shop headings: New Spares | Used Spares | Accessories | Brands
Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap
Stop light switch also known as Guzzi ref. 63657000
More than 5 in stock
79654116 GU79654116 79 65 41 16
7965 4116 7965.4116 79.65.41.16
Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2
£21.40
INC VAT
£17.83 EX VAT
Stainless steel brake disc mounting bobbin
5 in stock
28613560 GU28613560 28 61 35 60
2861 3560 2861.3560 28.61.35.60
£10.50
INC VAT
£8.75 EX VAT
Pair of EBC FA209 brake pads, used for front brake pads on Quota and Bellagio, rear brake pads for Cali 1400, Cali EV, Cali Stone, Cali Jackal and Special. All use Brembo PF2.3032 caliper
Also known as Guzzi ref. 30654626, AP8113627
5 in stock
03654600-z 03654600 GU03654600 03 65 46 00
0365 4600 0365.4600 03.65.46.00
£18.90
INC VAT
£15.75 EX VAT
Ball bearing for brakelight switch
5 in stock
92295708 GU92295708 92 29 57 08
9229 5708 9229.5708 92.29.57.08
£0.90
INC VAT
£0.75 EX VAT
Dimensions:
10mm threaded shank, 11mm across flats, 8mm OD at base, 15mm from tip to underside of flats
Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models
Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.
5 in stock
£8.20
INC VAT
£6.83 EX VAT
Rubber brake cable sleeve for lower end of cable
4 in stock
12626300-z 12626300 GU12626300 12 62 63 00
1262 6300 1262.6300 12.62.63.00
£8.30
INC VAT
£6.92 EX VAT
Brembo brake master cylinder overhaul kit for handlebar, undertank (cable operated) mounted, handlebar mounted and rear PS 12 master cylinders. Contains seals, brake grease, spring and piston. PS12 handlebar master cylinder fitted to early 850 and 1000 models. PS12 rear master cylinder fitted to Nevada 750
This seal kit is also known as 082039797. NB repair kit instructions refer to rear master cylinder. To fit this to a PS12 handlebar mounted cylinder you will need to punch the old piston out using a thin drift through the hole at the banjo bolt end of the master cylinder. Carefully note the order of the ring and washer as the piston comes out and replace with components from kit. Brembo no. 110279720. See this link for help with fitting this kit
4 in stock
17659352 GU17659352 17 65 93 52
1765 9352 1765.9352 17.65.93.52
Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei, Laverda Montjuic, Harris F1
£28.50
INC VAT
£23.75 EX VAT
Brembo kit containing replacement seal and angled elbow for connecting remote brake fluid reservoir to PS 15, PS 11 and PS 13 rear master cylinders
Also known as Brembo ref. 110312720
4 in stock
19659500 GU19659500 19 65 95 00
1965 9500 1965.9500 19.65.95.00
£7.50
INC VAT
£6.25 EX VAT
Brembo caliper cover for models with P2 F08 (P8) single bleed nipple calipers
You may need to immerse the cover in warm water before fitting
4 in stock
17654760 GU17654760 17 65 47 60
1765 4760 1765.4760 17.65.47.60
£12.50
INC VAT
£10.42 EX VAT
Pair of EBC FA095 brake pads for Brembo 5165 single pin four piston calipers
We advise checking your front caliper(s) have one not two pad pins
4 in stock
30654602-z 30654602 GU30654602 30 65 46 02
3065 4602 3065.4602 30.65.46.02
Also fits Magni Sfida
£18.80
INC VAT
£15.67 EX VAT